9211 Cockleshell Court, Suite B2, Bonita Springs, FL
(239) 676-5934
Mon. - Fri. 8:00 am - 5:00 pm | Sat. 9:00 am - 2:00 pm

Multiecuscan Software

$59.95

Diagnostic and data logging software and various cables.  Free ground shipping to lower 48 states.

Add To Wishlist

Description

Multiecuscan is a vehicle diagnostic software with advanced functions. It allows you to perform various diagnostics tasks on the supported vehicles/modules. In order to use the software you need an interface. The following interfaces are currently supported by the software: KL (also known as VagCom 409), ELM327 (1.3 or newer), OBDKey 1.40, OBDLink, ELM Scan 5, CANtieCAR.
Bluetooth OBDKey, ELM 327 and OBDLink interfaces are fully supported but not recommended for special functions (like PROXI Alignment, remote control programming, IMA coding, etc.)!
CANtieCAR is a professional multi-protocol interface with multiplexing capabilities.

This is recommended for modern Alfas and Fiats with a OBD port.

A OBD cable which is sold separately is needed to connect to your laptop. $64.95 shipped sold separately.

 

In addition we offer an optional 6 cable set that will allow you to connect to other functions:   $59.95 shipped sold separately,

For use with Multiecuscan software. You must have the OBD cable to adapt to these.
FiatECUScan Adapter Cable Bundle
Cable length: 22cm
Note: There are only used as a connecte cable and does not contain any software or diagnostic cables
There are 6 adaptor cables included which perform different functions.
Green ABS / Power Sreeing adapter lead ( “Adapter 1” on Multi-ECUScan website)
-Designed to allow access to the ABS and Power Steering systems on supported vehicles. This adapter has a green connector on one end for easy identification.
Using this adapter, Pin 7 on the diagnostic tool is connected to Pins 1,7,9 & 12 on the car.
Red Airbag adapter lead ( “Adapter 2” on Multi-ECUScan website)
-Designed to allow access to the Airbag system on supported vehicles.
This adapter has a red connector on one end for easy identification.
Using this adapter, Pin 7 on the diagnostic tool is connected to pin 3 only pn the car.
Yellow CAN adapter lead ( “Adapter 3” on Mult-iECUScan website)
-Designed to allow access to the low-speed CAN system on supported vehicles.
This adapter has a yellow connector on one end for easy identification.
Using this adapter, Pin 6 & 14 on the diagnostic tool are connected to pins 1 & 9
Respectively on the car, Pin 7 on the diagnostic tool is connected to pin 12 on the car.
Purple Electric hood adapter lead ( “Adapter 4” on Multi-ECUScan website)
-Designed to allow access to the electric hood system on supported vehicles.
This adapter has a purple connector on the end for easy identification.
Using this adapter, Pin 7 on the diagnostic tool is connected to pins 7,8,11 & 13 one the car.
Blue Control Module Adapter Wire Design allows access to enhanced features on the vehicle (eg, multimedia, blind spot sensors, etc.)
Gray base control module adapter wire designed to allow access to basic functions on the vehicle (eg headlights, parking controller, ABS, electric steering, etc.)
Packing List:
6 x ECU connector cables for Fiat
PROFESSIONAL FOR FIATECU SCAN ADAPTER OBD OBD2 CONNECTOR MULTI SCAN ABS AIRBAG OBD2 SCANNER DIAGNOSTIC CABLE FOR FIAT ECU SCAN
No photo description available.

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

DICorse
These cars have been our passion since 1971. We carry many hard to find quality OE replacement parts and top of the line aftermarket parts in stock!
Contacts

(239) 676-5934

Mon. - Fri.8:00 am - 5:00 pmSaturday-9:00 am - 2:00 pm

DICorse
DICorse.com ©2021 | All Rights Reserved.